RT60 is the reverberation time of a space: the time, in seconds, that sound energy needs to decay by 60 decibels after the source stops. In audio work and room Acoustics, it is the single most widely quoted number for describing how live or dry a room sounds, and it guides decisions about recording rooms, control rooms, concert halls, classrooms and offices.
A decay of 60 dB means the sound pressure level falls to one millionth of its original intensity, roughly the point where a loud event becomes inaudible against a quiet background. Because RT60 summarizes the combined effect of room volume and surface absorption, it is a practical bridge between the physics of reverberation and the everyday judgment of whether a room is suitable for speech, music or monitoring.
How RT60 is defined and measured
RT60 is measured by exciting a room with sound and recording how the level falls once the excitation ends. Practitioners plot the energy decay curve and read the slope, expressed in decibels per second, then extrapolate it to a full 60 dB drop. The standard procedure is described in ISO 3382, which covers performance spaces, ordinary rooms and open-plan offices.
A full 60 dB of clean decay is rarely available above the background noise, so measurements usually use a shorter range. T20 fits the decay between -5 dB and -25 dB and multiplies the time by three; T30 fits -5 dB to -35 dB and multiplies by two. A closely related measure, early decay time (EDT), uses the first 10 dB and correlates better with perceived reverberance.
The excitation signal determines measurement quality. Impulsive sources are quick but noisy, while swept-sine and MLS signals produce a clean impulse response from which the decay curve is derived by Schroeder backward integration. The table below compares the common methods.
| Method | Excitation | Strength | Weakness |
|---|---|---|---|
| Interrupted noise | Pink noise switched off | Simple, robust | Requires averaging several decays |
| Balloon or starter pistol | Impulse | Fast, portable | Poor repeatability and low-frequency energy |
| Exponential sine sweep | Swept tone | High signal-to-noise ratio | Sensitive to movement during the sweep |
| MLS sequence | Pseudo-random noise | Good noise rejection | Sensitive to distortion and time variance |
The Sabine and Eyring equations
RT60 can be predicted before construction with simple formulas. Wallace Sabine established that reverberation time is proportional to room volume and inversely proportional to total absorption. In metric units the Sabine equation is RT60 = 0.161 V / A, where V is the volume in cubic meters and A is the total absorption in metric sabins, the sum of each surface area multiplied by its absorption coefficient.
Sabine’s formula assumes a diffuse sound field and works well in fairly live rooms with average absorption coefficients below about 0.2 to 0.3. In heavily treated rooms it overestimates the time, so the Eyring equation, which uses a logarithmic term for absorption, gives more realistic values. Neither formula handles uneven absorption well, which is why designers increasingly use ray-tracing and image-source simulation.
| Approach | Best suited to | Main limitation |
|---|---|---|
| Sabine equation | Live rooms, early design estimates | Overestimates RT60 in absorbent rooms |
| Eyring equation | Rooms with higher average absorption | Still assumes a diffuse field |
| Fitzroy and Arau-Puchades | Rooms with absorption concentrated on some surfaces | Empirical, less widely validated |
| Geometric simulation | Complex shapes, final design checks | Accuracy depends on input data and low-frequency modeling |
Frequency dependence of reverberation time
RT60 is not a single value for a real room, because absorption varies strongly with frequency. Measurements are therefore reported in octave or third-octave bands, typically from 125 Hz to 4 kHz. Thin porous panels absorb high frequencies efficiently but do little below 250 Hz, so many rooms show a long low-frequency tail and a short treble decay.
A balanced room keeps the curve reasonably flat across bands, often allowing a modest rise at low frequencies in music halls to add warmth. In small rooms below roughly 200 Hz, behavior is dominated by room modes rather than a statistical decay, and a single RT60 figure there can be misleading; modal ringing at specific frequencies matters more than the averaged time.
Single-number summaries such as T mid, the average of the 500 Hz and 1 kHz bands, are convenient for specifications but should always be read alongside the full band data.
Typical RT60 targets by room type
The appropriate RT60 depends on room purpose and volume. Speech needs short decay for intelligibility, while orchestral and choral music benefits from longer decay that blends notes. The ranges below are typical mid-frequency targets; larger rooms generally tolerate longer times.
| Room type | Typical RT60 | Priority |
|---|---|---|
| Recording control room | 0.2-0.4 s | Accurate monitoring |
| Vocal booth | 0.1-0.3 s | Dry, uncolored capture |
| Classroom | 0.4-0.7 s | Speech intelligibility |
| Home theater | 0.3-0.5 s | Clear dialogue and imaging |
| Concert hall | 1.8-2.2 s | Envelopment and blend |
| Large cathedral | 4-8 s or more | Liturgical music, not speech |
Building codes and design guides in many countries set maximum reverberation times for schools and healthcare spaces, because excessive decay raises noise levels and fatigue. Designers usually aim for the lower end of a range when a room must serve speech and amplified sound.
Controlling RT60 with acoustic treatment
Reducing RT60 means adding absorption in the right frequency bands. Porous absorbers such as mineral wool panels handle mid and high frequencies, while bass traps, membrane absorbers and Helmholtz resonators target low frequencies. Increasing RT60 is achieved by removing absorption or adding volume, and diffusers can make a decay sound more even without changing its length much.
| Symptom | Likely cause | Remedy |
|---|---|---|
| Boomy low end | Long low-frequency RT60, room modes | Thick bass traps in corners |
| Dull, lifeless sound | Too much thin high-frequency absorption | Replace foam with broadband panels or diffusers |
| Poor speech clarity | Overall RT60 too long | Absorptive ceiling and wall panels |
| Flutter echo | Parallel reflective surfaces | Absorb or diffuse one surface of each pair |
A common mistake is treating RT60 as the only goal. A room can meet its target and still suffer from strong early reflections, flutter echo or modal peaks, so experienced acousticians combine RT60 with clarity metrics such as C50 and C80, and with listening tests.
Limitations and common misconceptions
- RT60 is not echo. An echo is a distinct, delayed repetition; reverberation is a dense, continuous decay.
- Soundproofing does not lower RT60. Isolation stops sound passing between spaces, while absorption shortens decay within a space.
- One number is rarely enough. Band values, EDT and clarity indices reveal problems an average hides.
- Small rooms defy statistics. Below the Schroeder frequency, modal behavior dominates and RT60 loses meaning.
- Occupancy matters. An audience adds substantial absorption, so empty-room and occupied RT60 can differ noticeably.
In everyday language
RT60 tells you how long a room keeps ringing after a sound stops. Clap your hands in a stone church and the sound hangs in the air for several seconds. Clap in a bedroom full of furniture and it disappears almost at once. RT60 puts a number on that difference.
The key idea is simple: hard, empty, large rooms ring longer, and soft, furnished, small rooms ring less. Too much ringing makes speech muddy, while too little can make music feel flat. Good rooms have the right amount for their purpose.
Seen in the real world
A small production company converts a 40 cubic meter spare room with plaster walls and a wooden floor into a voice-over studio. An exponential sweep measurement shows an RT60 of about 0.9 s at 500 Hz and nearly 1.3 s at 125 Hz, and test recordings sound hollow and roomy.
The engineer installs 10 cm mineral wool panels on the side walls and ceiling, adds corner bass traps and places a rug on the floor. A second measurement shows about 0.25 s at mid frequencies and 0.4 s at 125 Hz. Narration now sounds close and clean, and editors no longer need to apply heavy noise and reverb reduction in post-production.