Cell-to-pack (CTP) is a traction battery architecture in which cells are mounted directly into the pack enclosure instead of being grouped first into separate modules. In EV batteries, the approach removes a layer of housings, end plates, wiring and fasteners, which frees space for more active material and raises pack-level energy density while reducing parts count and assembly cost.
The concept matters for electric vehicles because the module layer of a conventional pack can consume a significant share of volume and mass without storing any energy. CTP is a packaging and integration strategy, not a cell chemistry, so it can be combined with LFP, NMC or sodium-ion cells.
How cell-to-pack integration works
A conventional battery pack follows a three-level hierarchy: cells are assembled into modules, and modules are assembled into the pack. Each module carries its own frame, compression plates, cell monitoring electronics and busbars, which simplifies handling and service but adds inactive mass and volume.
Cell-to-pack collapses this hierarchy into two levels. Cells, usually large prismatic or long blade-format cells, are placed in rows inside the pack tray, and the cells themselves carry structural loads that modules previously handled. Cooling plates, busbars and sensing harnesses are routed across the whole pack rather than repeated in each module.
The table compares the three main integration levels used in current EV batteries.
| Architecture | Hierarchy | Main characteristic |
|---|---|---|
| Cell-to-module-to-pack | Cell, module, pack | Modular, serviceable, lower density |
| Cell-to-pack | Cell, pack | No modules, higher volume utilization |
| Cell-to-body or cell-to-chassis | Cell, vehicle structure | Pack lid or floor forms part of the body |
Effects on energy density, mass and cost
The central metric for CTP is volume utilization, the share of pack volume occupied by cells. Traditional module-based packs typically reach about 40 to 50%, while CTP designs commonly report about 60 to 75%, depending on cell format and cooling layout.
Because the cells are unchanged, the gain appears at pack level rather than cell level. Removing modules also eliminates many parts and assembly steps, which reduces cost per kilowatt-hour. The ranges below are indicative and vary by manufacturer and chemistry.
| Property | Module-based pack | Cell-to-pack |
|---|---|---|
| Volume utilization | 40 to 50% | 60 to 75% |
| Gravimetric gain | Baseline | About 10 to 15% higher |
| Parts count | Baseline | Up to about 40% fewer |
| Assembly complexity | Many module operations | Fewer, larger operations |
| Repairability | Module replacement possible | Often whole-pack replacement |
CTP has been especially important for LFP chemistry. LFP cells have lower cell-level energy density than NMC cells, but their thermal stability allows tighter packing, so CTP lets LFP packs approach the pack-level density of older NMC module designs at lower cost.
Cell formats and design variants
Cell-to-pack is easiest with large-format cells that can span much of the pack width and resist mechanical loads. Smaller cells require more fixtures and connections, which reduces the benefit of removing modules.
| Cell format | CTP suitability | Key consideration |
|---|---|---|
| Long prismatic or blade cell | Very high | Cells act as structural beams |
| Standard prismatic cell | High | Needs compression and side frames |
| Large cylindrical cell | Moderate to high | Packed in arrays with adhesive or potting |
| Pouch cell | Moderate | Needs external support against swelling |
Known industrial implementations include the BYD Blade Battery, which uses long LFP cells arranged across the pack, and the CATL Qilin design, which integrates cooling between cells. Several manufacturers also develop cell-to-body variants in which the pack top cover doubles as the cabin floor, pushing integration one step further.
Thermal management and safety in CTP packs
Removing modules also removes natural barriers between cell groups, so thermal design becomes more critical. In a module-based pack, a failure can often be contained within one module; in a CTP pack, the design must prevent thermal runaway propagation across a single large cell array.
- Thermal barriers: mica sheets, aerogel pads or ceramic layers between cells slow heat transfer during a fault.
- Integrated cooling: cooling plates under or between cells serve the entire pack, which improves temperature uniformity.
- Venting paths: directed gas channels guide hot gases away from neighboring cells and the cabin.
- Pack-level BMS: the battery management system monitors cell voltages and temperatures without per-module boards, using fewer but longer sensing harnesses.
Regulatory requirements such as UN ECE R100 and the Chinese GB 38031 standard include thermal propagation tests, which encourage manufacturers to demonstrate that a single-cell failure gives occupants sufficient warning and escape time.
Trade-offs, repair and end-of-life questions
The main disadvantage of cell-to-pack is reduced serviceability. Cells are often bonded with structural adhesives or potting foam, so replacing a single faulty cell or group can be impractical, and a local defect may lead to replacement of the entire pack.
| Aspect | Advantage | Drawback |
|---|---|---|
| Range | More cells fit in the same space | Benefit depends on cell format |
| Cost | Fewer parts and assembly steps | Higher scrap cost if a pack fails |
| Service | Simpler pack-level diagnostics | Limited cell or module repair |
| Recycling | Fewer component types | Adhesives complicate disassembly |
For battery recycling, bonded CTP packs can slow mechanical disassembly, although the reduced number of component types may simplify sorting. Engineers therefore weigh density and cost gains against repairability, and some designs use removable fasteners or debondable adhesives to keep end-of-life processing practical.
Put simply
An electric car battery is made of many small cells. In older designs, the cells were first packed into small boxes called modules, and those boxes were then packed into one big battery case. Cell-to-pack skips the small boxes. The cells go straight into the big case.
Imagine packing eggs for a trip. Instead of putting every carton into a larger crate, you design the crate so the eggs sit firmly in it on their own. More cells fit in the same space, which means more driving range and a cheaper battery, but fixing one broken cell becomes harder.
In practice
An automaker is updating a compact electric crossover whose floor can hold a battery volume of about 300 liters. The previous model used NMC modules and stored 60 kWh, but the company wants lower cost without losing range.
The engineering team switches to long LFP cells in a cell-to-pack layout. Volume utilization rises from about 45% to about 68%, so the same space now holds about 64 kWh of LFP cells, even though each LFP cell stores less energy than the NMC cell it replaces. The pack also has roughly a third fewer parts, which shortens assembly time on the production line.
The trade-off appears in the service plan. Dealers can no longer replace an individual module, so the warranty process changes to whole-pack replacement and remanufacturing at a central facility, where packs are refurbished and returned to service.