An under-display camera (UDC) is a front-facing camera module mounted behind the active display panel, so that the screen continues to show pixels directly above the lens instead of leaving a notch, a punch hole or a pop-up mechanism. In mobile hardware, it is the most ambitious answer to the goal of a truly uninterrupted full-screen design on smartphones, tablets and laptops.
The idea is simple, but the engineering is not: the camera must capture enough light through layers of OLED pixels, wiring and polarizing film, and the display must look normal over the camera area. Every current implementation is therefore a compromise between image quality and screen uniformity, and understanding that compromise explains why the technology remains a niche feature rather than a standard one in the Mobile industry.
How an under-display camera sees through the screen
An under-display camera works by making a small region of the display partially transparent to visible light. A standard OLED panel lets only a few percent of incoming light pass, because opaque thin-film transistors, metal traces, the cathode layer and the circular polarizer block or absorb most of it. Manufacturers therefore redesign the area above the lens, often called the camera display region or transparent zone, while the rest of the panel stays unchanged.
Three techniques are combined in most designs. First, the pixel density is reduced over the lens, leaving gaps between subpixels. Second, the driving circuitry is moved to the edge of the region or replaced with transparent conductors such as indium tin oxide. Third, some panels remove or modify the polarizer in that zone. The result raises transmittance from roughly 2-5% to roughly 20-40%, which is still far below an open aperture.
The following table summarizes the layers that obstruct light and how engineers address each one.
| Layer | Effect on the camera | Typical countermeasure |
|---|---|---|
| Pixel array | Blocks and scatters light | Lower density or smaller pixel apertures |
| Thin-film transistor backplane | Opaque circuitry in the light path | Relocated drivers, transparent wiring |
| Circular polarizer | Absorbs about half of the light | Removed or replaced in the camera zone |
| Cathode layer | Partly reflective metal film | Patterned or thinned cathode |
| Cover glass | Minor reflection and haze | Anti-reflective coating |
Image quality challenges and computational correction
Even an optimized panel degrades the image in predictable ways. The regular grid of pixels and wires acts as a diffraction grating, so point light sources produce starburst flares and halos. Reduced transmittance lowers the signal, which raises noise in low light, and the scattered light reduces contrast and fine detail. Color can also shift because different subpixel materials pass wavelengths unequally.
Manufacturers rely heavily on computational photography to recover quality. Image signal processors and neural processing units in the Mobile SoC run models trained to remove the known diffraction pattern, a process related to deconvolution with a measured point spread function. Multi-frame stacking reduces noise, and dedicated models suppress flare. These steps narrow the gap, but they cannot fully restore information the display never let through.
The table below links the typical artifacts to their causes and to the usual software response.
| Artifact | Physical cause | Main correction |
|---|---|---|
| Haze and low contrast | Light scattering in panel layers | Dehazing and local contrast models |
| Starburst flare | Diffraction by the periodic pixel grid | Flare removal networks, PSF deconvolution |
| Low-light noise | Low transmittance of the camera region | Multi-frame noise reduction |
| Color cast | Wavelength-dependent transmission | Calibrated color correction per unit |
| Softness | Loss of high spatial frequencies | Learned sharpening and super-resolution |
Display side effects over the camera area
The display above the lens has its own trade-off. Because the camera region has fewer pixels per inch, it can appear slightly grainy or show a faint screen-door pattern, especially on white backgrounds or at close viewing distance. Early commercial devices had a camera region at roughly a quarter of the surrounding density, which made the area clearly visible.
Later generations increased the density in the transparent zone to match or nearly match the main panel and added pixel-level brightness compensation, which drives the remaining pixels harder so that luminance looks uniform. That approach raises a durability concern: subpixels that run brighter can age faster and burn in unevenly, so controllers apply compensation curves that track wear over time.
How it compares with other front camera designs
The under-display camera is one of several ways to fit a selfie camera into a phone, and each option ranks differently on screen area, image quality and cost. The comparison below shows why most flagship phones still choose a punch-hole camera while a few products accept the under-display trade-off.
| Design | Screen interruption | Selfie image quality | Main drawback |
|---|---|---|---|
| Notch | Large cutout at the top edge | High | Visible loss of screen area |
| Punch-hole | Small circular or pill cutout | High | Visible hole in content |
| Pop-up module | None when retracted | High | Moving parts, dust and water risk |
| Under-display camera | None or barely visible | Moderate | Lower image quality, higher cost |
| Bezel placement | None, thicker frame | High | Larger device body |
A related constraint concerns biometric hardware. Systems such as Face ID depend on infrared projectors and sensors that need clear optical paths, so hiding them under the display is even harder than hiding a visible-light camera. By contrast, an under-display fingerprint sensor works well because it needs only close-range contact imaging, not a focused view of a distant scene.
Where the under-display camera fits in practice
The technology suits devices where an uninterrupted screen matters more than selfie quality. Foldable phones have used it on the large inner display, where the camera serves mainly for video calls and an unbroken canvas improves reading and media. Some laptop and tablet concepts use it for the same reason. For users who take many selfies or record front-facing video professionally, a punch-hole design remains the stronger choice.
The decision table summarizes how the trade-off usually plays out.
| Priority | Better choice | Reason |
|---|---|---|
| Immersive media and gaming | Under-display camera | No cutout over content |
| Frequent selfies and vlogging | Punch-hole camera | Sharper images, better low light |
| Video calls on a foldable | Under-display camera | Adequate quality at call resolutions |
| Face-based secure unlock | Dedicated sensor cutout | Infrared paths need clear optics |
Limitations and common misconceptions
- It is not invisible in every condition. The camera region usually shows under certain angles, bright light or uniform backgrounds.
- Resolution figures can mislead. A high megapixel count does not compensate for reduced light transmission, so effective detail is often lower than on a punch-hole camera.
- Software carries much of the result. Image quality depends strongly on processing models and calibration, so two devices with similar panels can differ markedly.
- Repairs are costlier. Replacing the screen may require recalibrating the camera correction, which ties the display and camera together.
- Wear is uneven. Brightness compensation can lead to faster aging of the camera-zone pixels over years of use.
In everyday language
An under-display camera is a selfie camera hidden behind the phone screen. Instead of a black dot or notch, the screen keeps showing the picture right over the camera, so the display looks complete.
The catch is that the camera has to look through the screen, a bit like taking a photo through a fine window screen. Some light gets lost and some gets scattered, so the phone uses smart software to clean up the photo. The key idea: a cleaner-looking screen in exchange for somewhat weaker selfies.
Seen in the real world
Consider a business consultant who uses a foldable phone as a pocket tablet. On the large inner display, she reads reports, edits spreadsheets and watches presentations, and the camera sits under the screen in the upper area. During reading and video playback, the camera region is practically unnoticeable, so documents and slides fill the whole panel without a cutout.
Several times a week she joins video calls from that inner screen. Calls stream at roughly 720p, where the under-display camera delivers acceptable detail after processing, and colleagues rarely notice a difference. When she wants a sharp portrait for a professional profile, she instead uses the main rear cameras or the outer screen’s punch-hole camera, which handle dim light and fine detail far better.
The outcome illustrates the typical balance: the under-display camera serves calls and convenience well, while demanding photography still goes to conventional cameras.