A safety fence is a fixed physical barrier that encloses the working envelope of an industrial robot and prevents people from reaching the hazard zone while the machine operates. In robot safety, it is the oldest and still the most widespread form of robot guarding: instead of detecting a person and reacting, the fence simply makes contact between human and robot physically impossible during automatic operation.
Within robotics, the fence is rarely a standalone device. It forms part of a safeguarding system that also includes interlocked access doors, emergency stop devices, a safety controller and often light curtains or a safety laser scanner at material openings. Its design follows the risk assessment of the cell and the requirements that ISO 10218 places on robot integrators.
How a safety fence protects people in a robot cell
A safety fence protects people by separating them in space from the robot rather than in time or by speed. As long as the perimeter is closed and every opening is either guarded or interlocked, the robot can move at full speed and payload without any person being exposed to impact, crushing or shearing hazards.
The fence works only if it is treated as one element of a closed loop. The access door carries an interlocking switch that signals the safety controller; opening the door triggers a protective stop before anyone can reach the robot. This is why the fence itself is a passive guard with no failure mode in the electrical sense, while the door interlock carries a required performance level determined under ISO 13849.
The main components of a typical fenced robot cell and their safety functions are listed below.
| Component | Function | Typical requirement |
|---|---|---|
| Mesh panels | Block access and reach-through | Aperture matched to safety distance |
| Posts and floor anchors | Keep panels rigid and fixed | Removable only with tools |
| Interlocked door | Allow entry, stop robot on opening | Coded switch or guard locking |
| Guarded openings | Pass parts in and out | Light curtain, tunnel or muting |
| Reset station | Restart after deliberate check | Placed outside with full view of cell |
Design parameters: height, aperture and distance
The effectiveness of a safety fence depends on geometry, because a person can reach over, under or through any barrier that is too low, too high above the floor or too open. The governing reference is ISO 13857, which relates the height of the hazard, the height of the barrier and the horizontal safety distance a person must not be able to bridge with an arm, hand or finger.
Robot integrators usually choose a fence of about 2,000 to 2,200 mm in height, which keeps reach-over distances small for most robot envelopes. The gap at the floor is kept narrow so that nobody can crawl under, and the mesh aperture is selected so that fingers or a hand cannot reach a moving part on the other side. A larger aperture always demands a larger distance between the panel and the nearest hazard.
| Parameter | Typical choice | What it controls |
|---|---|---|
| Fence height | About 2,000 to 2,200 mm | Reaching over the top |
| Floor clearance | Small, often under 200 mm | Crawling or reaching under |
| Mesh aperture | Narrow slots or small square mesh | Reaching through with fingers or arm |
| Safety distance | Derived from ISO 13857 tables | Whether any reach meets the hazard |
| Panel strength | Rated for expected impacts | Containment of ejected parts or tooling |
Containment is a separate question from access. A fence that keeps people out may still fail to retain ejected parts, broken grippers or a dropped workpiece, so cells handling heavy loads or high speeds sometimes need solid or reinforced panels instead of standard mesh.
Safety fences compared with other safeguarding methods
A safety fence is the simplest and most robust safeguard, but it is not the only option. Electro-sensitive protective equipment and collaborative operating modes trade some robustness for flexibility and floor space, and each brings its own validation effort.
| Method | Principle | Main advantage | Main limitation |
|---|---|---|---|
| Safety fence | Physical separation | Simple and highly reliable | Large footprint, little flexibility |
| Light curtain | Detects body crossing a plane | Open access for loading | Needs a calculated stopping distance |
| Safety laser scanner | Monitors a floor area | Configurable warning and stop zones | Sensitive to layout and reflections |
| Speed and separation monitoring | Slows robot as person approaches | Shared space without barriers | Complex validation and sensing |
| Power and force limiting | Limits contact forces per ISO/TS 15066 | Direct human-robot collaboration | Low speed and limited payload |
In practice these methods are combined. A common layout uses a fence on three sides and a light curtain on the loading side, which keeps the robust perimeter where nobody needs access and sensing only where operators must interact with the process.
Planning and installing a fenced cell
Fence planning starts with the restricted space of the robot, which is the maximum envelope the robot can reach, reduced only by safety-rated limiting such as mechanical stops or certified software axis limits. Placing panels inside the full theoretical envelope without such limits creates a pinch point between the robot and the fence.
Integrators then decide where people must enter and why. Each reason for entry, such as teaching, cleaning, tool changes or jam clearing, needs a defined safe entry procedure, and longer interventions on energy sources call for lockout/tagout in addition to the door interlock.
| Situation | Recommended choice | Reason |
|---|---|---|
| Frequent manual loading | Light curtain or turntable at one side | Avoids constant door opening |
| Rare maintenance access | Interlocked door with guard locking | Prevents entry during rundown |
| Person can stand inside closed door | Presence detection or trapped-key system | Prevents unexpected restart |
| Heavy or fast payloads | Reinforced or solid panels | Contains ejected objects |
| Layout changes expected | Modular panel system | Allows relocation without redesign |
Before production, the integrator validates the installation against the risk assessment, verifies the door interlock function and records the result in the technical file. Any later change to the layout requires a renewed assessment rather than a quick adjustment of panels.
Limitations and common mistakes
A safety fence fails most often through defeat, bypass or poor detail, not through mechanical breakage. Experienced auditors look for the following recurring problems.
- Bypassed interlocks, for example a spare actuator taped into the switch, which turn the fence into decoration.
- Gaps at corners and floor created by uneven floors or missing panels after maintenance.
- Reset buttons inside the cell or without a view of the whole hazard zone, which allow restart with a person inside.
- Panels too close to the envelope, creating crushing points between robot and barrier.
- Missing reach-through check where conveyors or cable ducts pass through the fence.
A further limitation is economic rather than technical: a fence consumes floor space and makes cells harder to rearrange. This is one reason why human-robot collaboration has grown, although collaborative solutions only replace the fence when the risk assessment confirms that reduced speed and force are acceptable for the actual task.
In everyday language
A safety fence is the wall of mesh panels around a factory robot. It works like the fence around an animal enclosure at a zoo: the robot can move fast and with great force inside, and people stay safely outside.
The door in the fence has a switch. When someone opens it, the robot stops. The key idea is simple: if nobody can reach the robot, the robot cannot hurt anybody.
Seen in the real world
A metal parts supplier installs a six-axis robot that tends two CNC machines and lifts blanks of up to 25 kg. Because the robot moves quickly with heavy parts, collaborative operation is ruled out in the risk assessment, and the integrator encloses the cell with 2,200 mm mesh panels anchored to the floor.
Operators load raw blanks through a drawer station guarded by a light curtain, so they never open the main door during a shift. Maintenance staff enter through one interlocked door with guard locking that stays closed until the robot has stopped, and they apply personal padlocks before working on the grippers. After a year of operation, the cell has had no access-related incidents, and the only fence change was a reinforced panel added after a dropped part dented the original mesh.