Dark fiber

On this page 7

Dark fiber is optical fiber cable that has been installed in the ground or on poles but is not lit by the owner’s transmission equipment, so a customer can lease the bare glass and connect its own optics at both ends. In telecommunications, the term originally described spare strands laid in anticipation of future demand; today it also names a wholesale service in which an operator rents unlit fiber pairs to carriers, enterprises and data center operators.

Within fiber & broadband infrastructure, dark fiber sits at the most basic layer of the network. Instead of buying a fixed bandwidth such as 10 Gbit/s, the lessee buys physical transmission capacity and decides itself how much traffic to carry, which protocols to run and when to upgrade.

How dark fiber works as a leased asset

A dark fiber lease gives the customer exclusive use of one or more strands, usually a pair for transmit and receive, between two defined points. The owner remains responsible for the passive outside plant: ducts, cables, splice closures, manholes and repairs after cable cuts. The customer installs and operates all active equipment, including transceivers, amplifiers and multiplexers.

Fiber owners lay cables with many more strands than they need because civil works dominate the cost of a fiber route. Trenching, permits and restoration often account for 60-80% of deployment cost, while the glass itself is comparatively cheap. Selling or leasing the spare strands later turns that surplus into revenue. The table below shows how responsibilities are typically divided.

ElementResponsible partyNotes
Ducts, cable and splicesFiber ownerIncludes route maintenance and cable cut repair
Patch panels at handover pointsFiber ownerDefines the demarcation point
Optical transceiversCustomerChosen to match distance and data rate
DWDM or amplifier equipmentCustomerNeeded for high capacity or long spans
Network monitoring and routingCustomerOwner usually monitors only the physical path
Division of responsibilities in a dark fiber lease

Long-term leases are often structured as an indefeasible right of use (IRU), a contractual right to use specific strands for typically 10 to 25 years, paid largely upfront with an annual maintenance fee. Shorter monthly leases are common in metropolitan networks.

Key parameters when evaluating a dark fiber route

The value of a dark fiber route depends on its optical characteristics, not only its endpoints. A buyer requests test results, usually from an optical time-domain reflectometer (OTDR) and an insertion loss measurement, to confirm that the strands support the planned equipment. The following parameters matter most.

ParameterTypical valueWhy it matters
Fiber typeITU-T G.652.D single-modeSets attenuation and dispersion behavior
AttenuationAbout 0.2-0.35 dB/km at 1550 nmLimits span length without amplification
Splice lossBelow 0.1 dB per fusion spliceAccumulates on routes with many joints
Chromatic dispersionAbout 17 ps/nm/km at 1550 nmAffects high-rate transmission over distance
Route length1-80 km metro, longer with amplifiersDrives latency and optics selection
Optical parameters checked before leasing dark fiber

Physical route diversity is equally important. Two leased paths that share a duct or bridge crossing can fail together, so critical users ask for route maps and shared-risk information before signing. Latency-sensitive customers, such as trading firms, also compare the exact route length, since light in fiber travels at roughly 5 microseconds per kilometer.

Dark fiber compared with lit services

Dark fiber differs from lit services in who controls the transmission layer. With a lit service, the provider supplies a managed connection at a fixed rate; with dark fiber, the customer supplies the light. The comparison shows the main alternatives for connecting two sites.

OptionCustomer controlsCapacityTypical buyer
Dark fiberOptics, protocols, upgradesLimited only by equipmentCarriers, hyperscalers, large enterprises
Wavelength serviceTraffic on one leased wavelengthFixed, often 10-400 Gbit/sCarriers, content providers
Ethernet private lineTraffic onlyFixed, often 1-100 Gbit/sEnterprises, branch networks
Business broadbandTraffic only, shared networkContended, asymmetric or symmetricSmall and medium businesses
Dark fiber and alternative connectivity options

Dark fiber is a point-to-point physical medium, while access technologies such as GPON, XGS-PON and FTTH describe how lit fiber is shared among many subscribers. A network operator may lease dark fiber as the backhaul or middle mile and run its own PON equipment over it to serve homes.

Typical uses and buying decisions

Organizations choose dark fiber when they need very high or rapidly growing capacity, strict control over security, or predictable long-term costs. With dense wavelength division multiplexing (DWDM), a single pair can carry dozens of wavelengths at 100-400 Gbit/s each, so capacity grows by upgrading optics rather than renegotiating contracts.

SituationRecommended optionReason
Interconnecting data centersDark fiber with DWDMTerabit capacity at stable cost
Mobile network backhaulDark fiber or wavelengths5G sites need high capacity and low latency
Small office with modest trafficLit Ethernet or broadbandLower cost, no optical expertise required
Regulated data isolationDark fiberNo shared active equipment with other customers
Rural route without competitionWavelength serviceDark strands may be unavailable or costly
When dark fiber is a sound choice

The main trade-off is operational responsibility. A dark fiber customer needs staff or a contractor able to design optical links, keep spare optics and diagnose faults, which small organizations rarely have.

Limitations and common mistakes

Dark fiber is not automatically cheaper or more reliable than a lit service. Its economics depend on traffic volume, contract length and distance, and the owner’s repair commitments still decide how quickly a cut cable returns to service.

  • Ignoring shared risk: buying two strands in the same cable gives no real redundancy.
  • Skipping acceptance tests: undocumented splice loss can rule out planned optics.
  • Underestimating equipment cost: DWDM systems and spares add significant capital expense.
  • Overlooking repair terms: a weak service-level agreement can mean outages of many hours.
  • Assuming availability everywhere: dark strands are scarce outside metropolitan areas and major routes.

Regulators in several countries mandate wholesale access to passive infrastructure, including ducts and sometimes dark fiber, to encourage competition. Availability and pricing therefore vary considerably from one market to another.

The simple explanation

Dark fiber is like renting an empty pipe instead of buying water from a supplier. The glass cable is already in the ground, but nobody is sending light through it. The customer brings its own equipment and decides how much data to push through.

This gives full control and almost unlimited room to grow, but it also means the customer must run and repair the equipment at each end. It suits large organizations with heavy traffic far better than a household or a small shop.

How it is used in practice

A regional hospital group runs two data centers 35 km apart and needs synchronous replication of patient records and imaging archives. Instead of buying two 10 Gbit/s Ethernet lines, it leases two diverse dark fiber pairs on separate routes under a 15-year IRU.

The group installs a compact DWDM system carrying eight 100 Gbit/s wavelengths per route. Measured attenuation of about 9 dB per span allows unamplified transmission. When imaging volumes double three years later, the team adds wavelengths without changing the contract. Total capacity rises to 1.6 Tbit/s per route while the annual fiber cost stays the same, and a cable cut on one route causes no service interruption.