FTTC

Also known as: Fiber to the cabinet

On this page 7

FTTC, or fiber to the cabinet, is a broadband access architecture in which optical fiber runs from the exchange to a street cabinet, and the remaining distance to each home or business is covered by the existing copper telephone pair. Within the Fiber & broadband field of Telecommunications, it is the most widespread hybrid design between pure copper ADSL and full fiber.

FTTC delivers typical download speeds of 30 to 100 Mbit/s, and sometimes more, because it shortens the copper section to a few hundred meters. Its performance therefore depends heavily on distance from the cabinet and on the condition of the old copper line.

How FTTC connects the cabinet to the home

In an FTTC network, the operator installs an active street cabinet containing a DSLAM, the digital subscriber line access multiplexer, next to or inside the original copper distribution cabinet. Fiber connects the DSLAM back to the exchange, while short copper jumpers link it to the existing pairs that already run to each property.

The copper section carries the signal using VDSL2, a DSL technology defined by ITU-T Recommendation G.993.2. VDSL2 uses frequencies up to 17 MHz or more, which only works well over short copper runs because attenuation rises steeply with frequency and distance. The customer connects a VDSL2 modem or router to the telephone socket.

ComponentLocationFunction
Optical line to cabinetExchange to streetCarries aggregated traffic over fiber
Street cabinet DSLAMRoadsideConverts between fiber and VDSL2 signals
Copper distribution pairCabinet to buildingFinal link over legacy telephone cable
VDSL2 modemCustomer premisesTerminates the DSL signal
Power supply and coolingInside the cabinetKeeps active electronics running
Main components of an FTTC network

Speed, distance and VDSL2 profiles

FTTC speed is governed by the length and quality of the copper line. A home 200 m from the cabinet may synchronize near the maximum of its profile, while one at 1,000 m may achieve only a fraction of it. Crosstalk between pairs in the same cable bundle further reduces speeds as more customers connect.

Operators use several enhancements to push copper further. Vectoring, standardized in ITU-T G.993.5, cancels crosstalk by coordinating all lines in a bundle, while the 35b profile, often called super vectoring, extends the spectrum to about 35 MHz for very short lines. The table shows representative speeds; real results vary with cable gauge, joints and interference.

Copper lengthVDSL2 17aVDSL2 17a with vectoringVDSL2 35b
Under 300 m70-80 Mbit/s90-100 Mbit/sUp to 250-300 Mbit/s
300-600 m50-70 Mbit/s70-90 Mbit/s100-200 Mbit/s
600-1,000 m25-50 Mbit/s40-70 Mbit/sSimilar to 17a
Over 1,200 mBelow 20 Mbit/sBelow 30 Mbit/sNo meaningful gain
Representative FTTC download speeds by line length

Upload speeds are much lower, typically 10 to 40 Mbit/s, because VDSL2 allocates most of its spectrum to the downstream direction. FTTC is therefore an asymmetric service, unlike symmetrical broadband delivered over full fiber.

FTTC compared with other fixed access technologies

FTTC sits in a family of FTTx architectures that differ in how close the fiber reaches the user. The comparison below places it alongside its most common alternatives in fixed broadband.

TechnologyFinal link mediumTypical downloadKey trait
ADSLCopper from exchangeUp to 24 Mbit/sLong copper, low speed
FTTCCopper from street cabinet30-100 Mbit/sReuses existing lines
FTTdpCopper from distribution point300 Mbit/s-1 Gbit/sVery short copper with G.fast
FTTHFiber into the home1-10 Gbit/sFuture-proof, symmetrical
Cable internetCoaxial cable100 Mbit/s-1 Gbit/sShared DOCSIS segment
FTTC and related access architectures

Marketing sometimes labels FTTC as “fiber broadband”, which can mislead consumers into thinking the fiber reaches their property. Several regulators now require operators to distinguish full fiber from part-fiber services in advertising.

Why operators deploy FTTC

The main reason for FTTC is speed of rollout at low cost. Because the copper drop to each building already exists, operators avoid digging up driveways, entering homes and running new cables, which are the most expensive parts of any fiber build. One cabinet can serve a few hundred premises.

FTTC has therefore been a common transitional step toward full fiber in many European countries. The fiber already laid to cabinets can later be extended toward homes, so part of the investment carries forward. The table summarizes the strategic trade-offs that shape the decision.

FactorAdvantage of FTTCDrawback of FTTC
Capital costMuch lower per home passedCosts repeat when upgrading to FTTH
Time to marketMonths rather than yearsSpeed gains plateau quickly
Operating costReuses copper plantPowered cabinets need maintenance
PerformanceLarge step up from ADSLDistance-dependent and asymmetric
Future upgradeFiber already reaches the streetCopper limits long-term capacity
FTTC deployment trade-offs

Limitations and common faults

The weakest part of FTTC is the aging copper pair. Corroded joints, water ingress, poor internal wiring and old telephone extensions all reduce the signal-to-noise ratio, leading to lower sync speeds or frequent resynchronization. Each powered cabinet is also a point of failure during electrical outages.

  • Long lines far from the cabinet may perform little better than ADSL.
  • Electrical interference from faulty power supplies or lighting can cause errors on the copper.
  • Dynamic line management may lower speeds after instability to protect reliability.
  • Copper switch-off plans in many countries mean FTTC has a limited remaining lifespan.

Many issues can be improved by using the master telephone socket, removing unfiltered extension wiring and replacing old modem filters. Line faults outside the property, however, require the operator to test and repair the copper pair.

Explained without jargon

FTTC is a way of delivering faster internet by running fiber cables only as far as the green box at the end of the street. From that box to the house, the connection still travels along the old telephone wire.

Think of it as a fast motorway that ends at the edge of the village, followed by a narrow local road. If the house is close to the box, the journey is quick. If it is far away, the narrow road slows everything down. The key point is that FTTC is faster than old ADSL, but slower and less reliable than fiber all the way to the home.

A typical use case

A family of four lives in a suburban house about 350 m from the nearest street cabinet. Their operator upgraded the area from ADSL to FTTC with vectoring, and their VDSL2 modem now synchronizes at about 78 Mbit/s download and 18 Mbit/s upload, compared with roughly 9 Mbit/s on the old service.

That capacity comfortably supports two 4K video streams, video calls for remote work and online gaming at the same time. The parents notice that uploading large work files is still slow, a direct result of the asymmetric VDSL2 design. After a technician moves the router to the master socket and removes an old extension cable, the line stops resynchronizing during evenings.

The outcome is a substantial upgrade at no construction cost to the household, while the operator plans to replace the copper with FTTH within a few years.