Nano-SIM

On this page 7

A Nano-SIM is the fourth form factor (4FF) of the removable SIM card, a plastic carrier of only 12.3 × 8.8 × 0.67 mm that holds the UICC chip a phone uses to identify its subscriber to a mobile network. Within SIM & eSIM technology in telecommunications, it is the smallest physical card in everyday use and the default slot format in nearly every smartphone sold since the mid-2010s.

The Nano-SIM does not change what a SIM does; it changes how much plastic surrounds the chip. The same subscriber credentials, IMSI and authentication keys live inside a nano card as inside its larger predecessors, which is why operators can ship one card that fits every device.

How the Nano-SIM form factor is defined

The Nano-SIM is defined as the 4FF form factor in the ETSI smart card specification TS 102 221, which was amended in 2012 to add it. The standard fixes the outline, the corner chamfer that keys the card into the slot, the thickness and the position of the contacts, so that any compliant card fits any compliant reader.

Physically, the card is little more than the contact module itself with a thin plastic border. Its electrical interface follows ISO/IEC 7816: the module exposes the same contact pads used by every SIM generation, including supply voltage, reset, clock, ground and the bidirectional I/O line. A sixth pad may carry the Single Wire Protocol used for NFC secure elements.

The table below lists the key dimensions that a device designer or a buyer of replacement trays needs to know.

PropertyValueWhy it matters
Width and height12.3 × 8.8 mmSets the tray outline
Thickness0.67 mmThinner than older cards
AreaAbout 108 mm²Roughly 40% smaller than 3FF
KeyingOne chamfered cornerPrevents reversed insertion
Contact layoutISO/IEC 7816 padsSame electrical interface as 2FF
StandardETSI TS 102 221 (4FF)Guarantees slot compatibility
Nano-SIM physical specification

Nano-SIM compared with other SIM form factors

Each SIM generation removed plastic, not capability. The original credit-card-sized SIM gave way to the Mini-SIM, then the Micro-SIM, and finally the Nano-SIM, while the chip and its contact module stayed essentially the same. The decisive change with 4FF was a reduced thickness of 0.67 mm instead of 0.76 mm, which saves height inside slim devices.

The following comparison shows how the removable formats relate to each other and to the soldered embedded format.

Form factorDimensions (mm)Thickness (mm)Typical use today
1FF full-size85.6 × 53.980.76Carrier for punch-out cards
2FF Mini-SIM25 × 150.76Older phones, some routers
3FF Micro-SIM15 × 120.76Legacy tablets and modems
4FF Nano-SIM12.3 × 8.80.67Almost all current phones
MFF2 embedded5 × 6Soldered packageIoT devices, many eSIM chips
SIM form factors side by side

The Nano-SIM also differs from the eSIM, which is not a card at all but an eUICC chip soldered to the board and loaded with operator profiles through remote SIM provisioning. A Nano-SIM carries one operator identity fixed at manufacture, whereas an eSIM can hold several downloadable profiles. The iSIM goes one step further by integrating the secure element into the main processor.

What the chip inside a Nano-SIM stores

Despite its size, the Nano-SIM hosts a complete secure microcontroller with its own processor, memory and operating system. It runs the USIM application for 3G, 4G and 5G access, and often an ISIM application for IMS voice services. The secret authentication key Ki never leaves the chip; the card computes responses to network challenges internally.

Several identifiers and settings are stored on or printed with the card, and each serves a distinct purpose.

ElementWhere it livesPurpose
ICCIDChip and printed on cardIdentifies the physical card
IMSIChip onlyIdentifies the subscriber to the network
Ki and OPc keysSecure chip memoryMutual network authentication
SIM PIN and PUKChip, with retry countersProtect against misuse of a lost card
Operator appletsChip memoryRoaming lists, menus, OTA updates
Data associated with a Nano-SIM

Because the identity is tied to the chip, moving a Nano-SIM to another handset moves the subscription with it. The phone keeps only its own hardware identity, the IMEI, which belongs to the device rather than to the subscriber.

Adapters, punch-out cards and trays in practice

Operators usually ship a triple-cut or multi-cut card: a full-size plastic frame with pre-scored outlines from which the user presses out a Mini-SIM, Micro-SIM or Nano-SIM. This lets one inventory item serve every device generation and removes the need to know the customer’s handset in advance.

Adapters work in the opposite direction and let a nano card sit in a larger slot. They are acceptable as a temporary measure, but the thickness difference and loose fit cause recurring problems, summarized below.

SymptomLikely causeRecommended fix
Card stuck in slotAdapter edge caught on contactsUse the native slot, extract carefully
No SIM detectedCard inserted upside down in trayAlign the chamfered corner
Intermittent signal lossWorn or dirty contactsClean pads, request replacement
Card not recognized after cuttingDamaged module or wrong thicknessOrder an official Nano-SIM
SIM locked after rebootsWrong SIM PIN entered three timesEnter the PUK from the operator
Common Nano-SIM handling problems

Trimming a Micro-SIM by hand into a nano outline was common when the format was new. It remains risky: the module can crack, and the card stays 0.09 mm too thick, which can jam spring-loaded readers. A free replacement card from the operator is the safer choice in almost every case.

Limitations of the Nano-SIM and its future

The Nano-SIM is close to the physical minimum for a removable card. Its plastic border is only about a millimeter wide, so a further shrink would expose the module to handling damage. Slots and trays still consume board space and require a waterproof seal and ejector mechanism, which is a cost designers increasingly avoid.

  • Physical loss or theft of the card removes connectivity instantly, although the PIN protects the subscription.
  • Changing operators requires shipping or collecting a new card, unlike downloading an eSIM profile.
  • Dual SIM phones often combine one Nano-SIM slot with one eSIM to balance flexibility and space.
  • A removable card offers easy transfer between handsets, which many users still value when traveling.

For these reasons the industry is moving toward eSIM-only designs, yet the Nano-SIM remains widespread because it works without any provisioning infrastructure, in every market and every network generation. A standard Nano-SIM may also become a target of SIM swap fraud only through the operator’s processes, not through the card format itself.

The simple explanation

A Nano-SIM is the tiny card you slide into a phone so that the mobile network knows who you are. It is about the size of a fingernail. Inside it is a small chip that holds your account details and a secret key, much like a key card that opens your hotel room.

Older SIM cards were bigger, but the chip was always the same. Manufacturers simply cut away more and more plastic. The key point is that the card size changed, while the identity inside stayed the same. If you put your Nano-SIM into another phone, your number and plan go with it.

How it is used in practice

A small logistics company equips 40 delivery drivers with new smartphones. The office manager orders business subscriptions from a mobile operator and receives 40 multi-cut SIM cards. For each phone, she presses out the Nano-SIM, opens the tray with the ejector pin, places the card with its chamfered corner aligned, and powers the device on.

Two drivers still use older rugged handsets for warehouse scanning, so their cards are pressed out at the Micro-SIM outline instead, with no adapter needed. When one driver later drops a phone into a canal, the manager moves the undamaged Nano-SIM into a spare handset within minutes. The driver keeps the same number and plan, and the company avoids waiting for a replacement card.