RGB parade

On this page 7

An RGB parade is a video scope that displays the red, green and blue channels as three separate waveforms placed side by side, each plotting signal level against horizontal image position. In color grading for video, it is the primary tool for judging channel balance, color casts and clipping with numbers rather than with the eye, which adapts to color and is easily misled by room lighting and display drift.

The parade is a variant of the waveform monitor: where a luma waveform shows one combined trace of brightness, the parade splits that information into its components so a colorist can see exactly which channel is too high, too low or out of range in each tonal region.

How an RGB parade maps the image

An RGB parade reads every pixel of the frame and plots its channel values in three adjacent cells. The horizontal axis of each cell corresponds to horizontal position in the picture, so an object on the left of the frame appears on the left of each cell. The vertical axis shows code value or signal level, from black at the bottom to peak white at the top.

Vertical position in the frame is discarded: all pixels in one column stack into a single vertical line of dots. Trace density indicates how many pixels share a level, so a large sky produces a bright, dense band, while a small highlight produces a faint speck. Reading the parade therefore means reading shapes and their relative heights across the three cells.

The scale on the left of the display can be expressed in several units. The choice matters, because the same signal appears at different numbers depending on the scale and the signal range.

ScaleBlack levelPeak whiteTypical use
10-bit code values64 (legal) or 0 (full)940 (legal) or 1023 (full)Precise grading and delivery checks
Percentage0%100%Quick reading in editing software
IRE or millivolts0 IRE / 0 mV100 IRE / 700 mVBroadcast engineering and legacy workflows
Nits (HDR PQ scale)0.0001 nits1,000 to 10,000 nitsHDR mastering
Common vertical scales on an RGB parade

Reading balance, casts and clipping

The central rule of the parade is simple: a neutral surface produces equal heights in all three channels. A white wall, a gray card or a black shadow should line up across the red, green and blue cells. When one channel sits higher than the others in a neutral area, the image carries a cast toward that channel, and when one sits lower, it carries a cast toward the complementary color.

Colorists usually check balance in three tonal zones separately, because a camera or lighting problem often affects shadows, midtones and highlights differently. Warm practical lights may tint only the highlights, while sensor noise or a poor black balance may tint only the shadows. This zone-by-zone reading maps directly onto lift, gamma and gain controls in primary color correction.

The following table links common parade patterns to their likely meaning in the image.

Pattern on the paradeLikely meaningTypical correction
Blue higher in highlightsCool cast in bright areasReduce blue gain or raise red gain
Red higher in shadowsWarm or muddy blacksLower red lift
Flat line at the top of one channelThat channel is clippedLower gain or recover from raw or log
Flat line at the bottomCrushed blacks in that channelRaise lift or lower contrast
All channels compressed in the middleLow contrast, flat log imageApply a transform or expand contrast
Uneven tops on a white objectHighlights not neutralBalance gain per channel
Parade patterns and what they indicate

Clipping deserves particular attention. A single channel can clip while luma still looks safe, which is common with saturated red stage lighting or blue LED fixtures. The luma waveform hides this problem, but the parade shows a hard horizontal ceiling in the affected cell, warning that detail and hue accuracy are already lost there.

RGB parade compared with other video scopes

The RGB parade is one of several scopes that complement one another, and no single scope answers every question. It excels at showing per-channel level and position, but it does not show hue or saturation directly. Experienced colorists keep at least the parade and the vectorscope open together.

ScopeWhat it showsStrengthBlind spot
RGB paradeEach channel level against horizontal positionChannel balance and per-channel clippingNo direct hue or saturation reading
Luma waveformBrightness against horizontal positionExposure and contrast at a glanceHides single-channel clipping
RGB overlayThree channels drawn on top of each otherFast check of neutrality where traces mergeOverlapping traces are hard to separate
VectorscopeHue as angle, saturation as distanceSkin tone line and gamut limitsNo brightness or position information
HistogramPixel count per levelOverall tonal distributionNo spatial location of tones
How the RGB parade differs from related scopes

A related variant, the YCbCr parade, shows luma and the two color-difference channels instead of RGB. It is useful for broadcast compliance because many delivery specifications are written in Y’CbCr terms, but the RGB version is more intuitive for creative balancing.

Using the parade in a grading workflow

In a typical session, the colorist normalizes the shot first with a color space transform or LUT, then uses the parade to set black and white points and neutralize casts before any creative look is applied. Grading tools such as DaVinci Resolve let the colorist click a neutral point or adjust per-channel lift, gamma and gain while watching the traces move.

  • Find a reference neutral such as a gray card, white shirt or concrete wall, and locate its column in the parade.
  • Balance the shadows by aligning the bottoms of the three traces with lift.
  • Balance the highlights by aligning the tops with gain, staying below the legal or target ceiling.
  • Check the midtones with gamma, watching skin and neutral surfaces in the middle of the scale.
  • Confirm with the vectorscope that neutrals cluster near the center and skin sits near the skin tone line.

The parade is also essential for shot matching. By placing the parades of two shots next to each other, the colorist can match the height of a face or a background across angles far more reliably than by comparing images visually, especially late in a long session when visual adaptation makes the eye unreliable.

SituationParade roleReason
Neutralizing a castPrimaryShows which channel deviates and in which tonal zone
Matching shots in a scenePrimaryCompares channel heights of the same objects
Legal range delivery checkShared with luma waveformCatches channel excursions above or below limits
Judging skin tone hueSecondaryThe vectorscope shows hue more directly
Deliberate stylized lookReference onlyIntentional imbalance is the creative goal
When the parade is the decisive scope

Limitations and common mistakes

The parade measures signal values, not intent, so balanced traces do not guarantee a good image. A sunset, a candlelit room or a teal and orange look is meant to be unbalanced, and forcing the traces level would destroy the mood. The scope tells the colorist where the image is; the creative decision remains human.

  • Neutralizing colored objects: a red car or green grass should not line up across channels, so balance must be judged only on surfaces known to be neutral.
  • Ignoring the signal range: confusing legal and full range shifts every reading and can cause false clipping warnings.
  • Reading the wrong color space: a parade on log footage before the transform shows compressed traces that do not represent the final picture.
  • Overlooking small areas: thin traces from small highlights are easy to miss, yet they may still clip on delivery.
  • Relying on the parade alone: without a calibrated monitor and the vectorscope, subtle hue errors can pass unnoticed.

In HDR work, the parade remains useful but must be read on a PQ or HLG scale, where equal vertical steps do not correspond to equal changes in light. Colorists should set the scope to match the mastering color space and transfer function, such as Rec. 709 for standard delivery or Rec. 2020 with PQ for HDR.

Explained without jargon

Every color on a screen is a mix of red, green and blue light. An RGB parade draws three small graphs, one for each of these colors, so you can see how much of each one the picture contains from left to right.

If something in the scene should be white or gray, the three graphs should reach the same height at that spot. When one graph is taller, the picture leans toward that color. The key idea is that the parade replaces guessing with measuring, much like a spirit level tells a carpenter whether a shelf is straight when the eye alone might be fooled.

A typical use case

A colorist is grading a corporate interview filmed in an office with large windows on one side and warm ceiling lights on the other. On the monitor the speaker looks slightly odd, but after several hours of work it is hard to say why. The RGB parade answers the question at once: in the column where the speaker’s white shirt sits, the blue trace rises about 40 code values higher in the highlights, while the shadows are neutral.

The colorist lowers blue gain and raises red gain slightly until the tops of the three traces align on the shirt, keeping peak white below 940 on the 10-bit legal scale for broadcast delivery. The vectorscope then confirms that skin sits near the skin tone line. The result is a neutral, consistent interview that matches the second camera angle within minutes instead of through repeated visual trial and error.